Wednesday, January 22, 2020

Rustic mirror frame made from Hazel

My daughter has a rectangular mirror (60 cm x 45 cm) that she wants to mount on a wall. We have two pieces of felled hazel about 8 cm in diameter that looked suitable for the task. Bex in in charge of the design and I'm helping  on the construction.
Our first job was to split the wood down the middle, but because of knots and the grain I decided it was best sawn with a rip saw. So we chose the best alignment to show of the features of the wood and did a straight rip down the centre line of each piece.
Starting point after ripping the Hazel logs.
After this the wood was left for over a year, mostly because Covid-19 made it difficult to work with Bex and also I was abroad for 5 months. Anyway, coming into Autumn 2022 and a few rainy days, we've decided to continue with the project. As expected the wood is now pretty dry having been left in the workshop in dry storage and also the half-cuts (shown above) have warped through drying, some of them more than others. This is probably made worse because of the inherent twisting in the original trunk of the tree. 
We started by looking at the two sides that we originally selected and decided that they were too bulky as they stand and also that we needed a straight edge on the inside to make a rebate to house the mirror. So work was started on preparing these two sides. The first job was to prepare a flat face on the original saw cut. For this I used a Veritas Scrub plane cutting across the grain and checking levels using a 1 m steel rule and  winding sticks for twist. Once this was done the face was smoothed with a smoothing plane and block plane. The intended inside edge was marked straight and planed to size making it square to the already prepared face. The next step was to reduce the thickness of the sides to about 2.5 cm. I did this using a home made kerfing saw (already discussed on this BLOG) to mark as best I could around the side as an aid to rip sawing the sides to size. This was impossible in some places where the curvature of the face was too steep but generally it was possible at the extreme ends of the sides and elsewhere did make a mark on the wood for guidance. I used the Roubo frame saw (details on this BLOG) to rip the sides to produce a planks with one planed face, a sawn face with one straight edge and a natural wavy edge (which will form the outside edge of the mirror).
This shows one of the sides below the saw already sawn to size and the other side being sawn with the Roubo type frame saw. The thickness of both pieces was 2.5 cm.

The sawn face was then planed to remove the saw marks and finally a No 80 cabinet scraper was used to smooth some tear-out which was difficult to remove with a well sharpened plane!

This shows two of the sides sawn and planed. These are 72 cm in length and may become the two rails. The shapes on these mirror each other as they were sawn from the same branch. The bark on the edges will not be removed for the moment.

Originally I was thinking of joining the frame with mortice and tenons joints but have decided to use lap joints that allow both rails and sides to overlap to give a more rustic look.  Because the bark is left on the outside of the sides, the overlap had to be carefully marked on the "bark side" and meant that a full overlap joint was difficult because of the oval shape of the bark. As a compromise, the joint was made to half of the depth of the side thickness to enable a close fit joint but keep the bark intact. In addition the joint will be strengthened using oak dowels through each of the lap-joints. 

Cutting the lap joins using a chisel and finishing with a Stanley no 71 router.

After the lap joints had been cut and adjusted to good fits using a fine wood file and carving knife, the rebates for the mirror housing were cut on the bottom and top rails. These were marked 1 cm longer than the rails on each side and 2 cm wide. The kerfing plane was used to saw and mark the width of the rebate. The rebate plane was tried but it was found to be difficult because of the end stops on the rebate, Instead a plough plane was used and the ends chiselled as needed,

The frame was then glued using G-clamps on each of the joints and kept flat using the wooden clamps as shown:
The frame glued before dowelling the joints.

The next step was to make rails to hold the mirror into the rebates along the top and bottom ends. I used some left over pieces of ash for this to fit across the rebates and also into them to make a snug fit, This proved quite difficult because the ash was very hard and difficult to rebate. I also made some rails to fit on the rear and glued on each side of the mirror. The final stage was to make a hanger that will be screwed to the rear of the mirror frame to aid fitting it to a wall. This was made from some of the left-over pieces of hazel.

The frame after a final sanding to remove pencil marks and after the first coat of Danish oil. The Danish oil darkens the wood considerable and shows the oak dowels to good effect. The two slats in the centre are to hold the mirror in the rebate at the rear.

The frame was then treated with Danish oil on both sides and also on the bark. Checking experiences on the internet with treating bark, Danish oil seems to be a popular method. Also the bark may last longer on the wood because it was felled in the winter when the sap wasn't rising. Also I have the feeling (based on no evidence apart from it's use in fencing etc!!) that hazel keeps it's bark intact better than many woods, but we'll see about that. So far with the varies planing and sawing, it has remained firmly attached to the wood. Hazel has quite a thick cambian layer under the bark which might help ? I will give the frame three coats of Danish oil over several days leaving at least 24 hours between coats.
Finished mirror after three treatments with Danish oil.

Rear view of the mirror with the rebate rails installed and the hanging mounts at the top. Couldn't resist writing the year and wood (hazel) on the mount!!


Tuesday, January 14, 2020

Spoon/knife carving, 2020

We are abroad for a while and I normally take some blanks for carving, usually on the beach in the sunshine or on our terrace. Here are some I'm taking this year:
A couple of beech blanks for making spoons for the coffee jar. I have made coffee spoons before but these have long handles. The new design is similar but the handles are going to be much shorted, "thumb print" size. 
This is my first attempt at making a folding spoon after the design of Jane Mickelborough. The mortice and tenon have been cut but not shaped yet. The pencil lines show the final shape being aimed for.
Beech ladle or scoop, not sure yet!! (side view)

Plan view of scoop/ladle.

These blanks were cut from a beech branch that had been split down the middle. The branch was from an ash tree felled at Dartington and may have been cut by mistake in the autumn. All the branch sections were curved so this was used for full advantage in designing the folding spoon and scoop. I also had some blanks for knives that are not shown above.

For the folding spoon, care was taken to keep the longitudinal grain at the hinge pin (where the halves of the spoon meet or fold). The wood was green and carved very well with a close grain. They were stored in a closed paper bag until being carved further.

I've just completed the first of the coffee spoons (blank is shown at the top). The handle is short so that the spoon can fit into the coffee jar. The beech wood was quite hard, probably it had dried more than I'd expected since collecting.
Coffee spoon carved from Dartington beech. This is smaller than I've made before so as to fit into the coffee jar. 

This side profile shows the angle of the handle that the thumb-hold made to the bowl. Beech is a close grain wood that is forgiving when carving but harder than birch.
I'll finish the sanding, drying and treatment with Walnut oil later.

The next item to finish was easier and similar to a butter knife I'd previously carved from Silver Birch. This time I'd used a splint of Ash that was roughly shaped with an axe and draw-knife so that the final shaping was relatively easy. I may use this as a camping knife on treks; yes it is lighter than titanium!

Butter knife made from Ash wood and similar to a design I'd found successful before for spreading butter etc and even when turning small pancakes on the gridle. 
Beech traveller's spoon

End profile of the above Beech spoon.
I carved this simple knife today whilst on the beach at Guardamar from a shard of Ash (Dartington) basically taking the design from some I'd seen in Sweden when touring. The wood was already dry.  I got a really smooth finish with sanding 80 grit to 320. I'll treat with Walnut oil later.

Ash knife that shows some interesting shades along the grain of the wood.
This is another knife made with Ash but this time with some teeth to aid cutting.
Ash knife that does the job on this "delicioso queso"
Now started to make a fork with more Ash. Firstly I marked a rough design and cut the tines after drilling the holes at the base of each piece to be cut out.
Limited tools here so cutting with a small axe-saw blade took a long time.
The carving was fairly straight forward and I tried to give some curvature to the fork but this was limited by the grain and thickness of the wood. I also had a small knot in the Ash that was revealed as I carved the handle so I had to make the handle slightly thicker than I'd wanted. I think the knot and colour was a result of dieback in the branch. This is my first fork and I am reasonable happy with the attempt. The test will come in using it!
Fork carved from a slice of Ash wood. This has had one treatment with walnut oil and after sanding (350 grit) I'll give it a second coat.
Spatula for camp cooking, also made from Ash.
Also tried some Ash spatulas that I thought might come in handy for camp cooking. Here is another that also has a knife edge.
Ash spatula with knife edge 
Next a second coffee spoon with a short handle, again made from beech that had more or less dried and so was hard carving which meant my knives had to be continually sharp. I have a couple of small diamond sharpeners that I bought along that are proving useful!!
Second coffee spoon (for the coffee jar) made from beech and yet to be treated to bring out the wood grain. The "thumb indent" was smaller than that on the previous spoon.

Side profile of the spoon above showing the downward curvature of the handle. The basic idea is for the spoon to fit inside a coffee jar and so remain with the jar for convenience.

Now making progress with the folding spoon. I roughly carved the handle and the spoon separately but have not made the hinge yet. I am concerned that drilling the hole for the pin hinge at this stage may be a mistake and prefer to get the spoon carved to something like it's final shape. The angle of the spoon to the handle is slightly less than the template that I am following and this will affect the hinge position. I noticed the hinge position described in the book is crucial to the spoon closing completely (Jane Mickelborough, " Make a Folding Spoon" Crafty Little Press, 2018).

The spoon is not joined yet and looks like this:
Top of spoon ready to carve,  fit the hinge and do the final spoon carving

Side view. Pencil lines are taken from the template but the hinge pin position has not been marked yet. The spoon bowl follows the direction of the beech grain

Bottom of the spoon. The symmetry looks good but there is still some adjustment to the tenon and mortice to get a closer fit before marking the hinge pin.
I managed to get a small hand-drill at the local second-hand market on Sunday so this evening I took the leap and drilled a hole for the hinge using the method described Jane Mickelboroughby. I did this in stages by marking the arcs as described by Jane and drilling the hole from both sides using a home made vice that I use for spoon carving from time to time. I think it is OK but at this stage the spoon doesn't close completely so I have a little refining to do (see some of my pencil lines in the photo below). The pin is a tight fit as I drilled the hole a slightly smaller diameter of the pin and this works fine once the pin is in place. When it folds, the mid-point of the handle lines up with the centre of the spoon as planned.
The folding spoon with the hinge pin in place. There is still a lot of refining to do, especially to allow the spoon to fold completely and get matching surfaces in the hinge area.

Today I finished the spoon by firstly removing wood to allow the spoon to fold completely. This was done carefully, more or less on the lines I had marked in the above photo. This was straight forward so I continued refining the surfaces before sanding. 
The finished spoon, the pin has to be fixed in place and wood treated.

The spoon when folded ready for travelling.

Side profile (handle not fully open here)
I am happy how it turned out as my first attempt, and it will be used because it's handy to pack and light weight for camping. It was challenging to carve even with the guide book. The main problem was getting the hinge in the right place so that the spoon closes and so is not under stress whilst folded, and having sufficient angle on the spoon to get the geometry right. It is important that the handle, hinge and spoon follow the grain of the wood so that is sufficiently strong, particularly at the hinge. I'll update later when I have had a chance to put it into use whilst camping.

I have now started the ladle, again of beech and with the shape determined by the grain of the wood. I have so far left the handle, just marking a centre line and a general shape. I thought it best to work on the bowl part whilst the handle is still quite chunky. So far most of the carving as been with a curved (or bent) gouge as a lot of material needed to be removed. I then used the curved knife to smooth the surface out. If I'd had my draw knife here, it would have been much easier to remove wood from the outside to get something closer to the shape I wanted to finish with, otherwise quite  hard work on the hard beech (now pretty dry) with the carving knife.
 Still a lot of carving on the bowl sides and base. As yet I haven't shaped the handle; hopefully it will be thinner and more curved as the shaping progresses.
The final shaping took some time as I tried to narrow the bowl sides and base and shape the handle. The knot shown in the photo above was difficult to avoid so I will probably fill in a small indent later.
The ladle is finished apart from treatment and attention to the knot.

Side profile of the bowl and shaped handle. The wood grain follows the shape of the handle and bowl.

Wednesday, November 20, 2019

Small stool in style of Japanese bath stool

In between other jobs I had some spare wood left to make a small stool for my grandchildren. I wanted to try another design so went for a stool with "through angled tenons". These joints I found quite challenging to do with hand tools but I persevered and so I include a few thoughts from this project here.
I made the top and legs from a 3.5 cm thick pine board. The finished stool was 36 cm long and 22 cm wide and the height was 24 cm. Pine isn't ideal for detailed joints because of the course grain and so takes more care to work and sharp tools. I used a section of 2 x 2 inches to make the stretcher connecting the two legs.
Stool after making the joints. Surface preparation (planing and sanding), preparing clefts, gluing and treatment yet to do.
The legs were set at an angle of 10 degrees from upright hence fixing the angle of the mortice and tenon joints on the two legs and stretcher. I set the angle on an angled bevel marker and this remained fixed for the entire job. the construction involved:
1. Marking out the two legs and sawing to shape. This can be just rectangular or truncated pyramid as shown. I also made a 5 cm cylindrical cut in the middle of the bottom of each leg and so made four balancing points for better stability of the stool. 
2. I decided to make two mortice and tenons on each leg to join them to the top of the stool. Basically the top was 12.5 cm wide and each tenon was 2.5 cm wide. The length of the tenon was about 5 cm to allow them to protrude out of the top so that the beech wedge could be added when gluing and then sawn/planed to the meet the top surface.
3. The most difficult part of the construction for me was cutting the mortices in the stool top. For this I made a small jig to clamp to the top and use as a chisel guide to get the correct angled mortice  (again 10 degrees).  I found that if I clamped the jig firmly to the top with a piece of plywood on the underside of the top, I could cut the mortice from one side right through to the plywood base. This worked well for all the joints. I made the jig by sawing/planing the correct angle on the face of a piece of beech and then cutting into three sections and then gluing together with the centre piece off- set.
Beech jig for cutting mortices. The face is angled at 10 degrees to the vertical and the width matches the tenons. The front "prongs" are also angled.
Finished stool after two coatings of Danish Oil. A further coating of clear polyurethane was applied after a couple of days. Now in full use by grandchildren.

Thursday, November 14, 2019

Stools from Green Wood

Autumn has come quickly this year (2019) and we're quite far into November and had for the first time temperatures below 5 C during the day. With all the rain over the last few weeks, there is not so much I want to do in the garden and I've put-off more pole lathe work until the weather improves. I made a hedgehog house with Sam using old timber from other jobs and that is now near the hedgerow at the rear of the garden. In between times I have collected locally some felled ash and silver birch green wood with the idea of making some green wood tripod stools. I read the book by Alison Ospina "Green Wood Stools" with lots of photos that gave me some ideas on designs and methodology. I'm not so keen on the stools with bark legs, mainly hazel, and prefer a more finished  approach (that are also illustrated in the book). Alison sets the legs in the base at 90 degrees thus avoiding the problems in drilling at an angle into the base and then uses the flexibility in the green hazel to bend the legs as needed. I wanted to use thicker wood for the legs and set the legs at an angle as I wouldn't have so much flexibility in the legs of the stool. 
The photo below shows a small stool I made on a one day course at Dartington and this was also made of ash wood and shaped with a draw knife and roughing plane.
Tripod stool made of green wood ash, height ??
The legs pass through the top and are held in place with walnut wedges. The legs where shaped with a "rounding plane" so they fitted into the holes in the top. The holes were drilled at an angle using a pillar drill making this bit of the construction much easier. The legs were shaped so that they were thinner at the top and bottom and roughly matched each other. This was done using a draw knife and refined using a large spokeshave plane. I did use sandpaper to finish it off although on the course they discouraged this; I guess it comes down to taste as some like the look of plane and chisel marks. The height of the stool is good for young children (both Sam, 5 years and Esmee, 3 years both use it either as a stool or table). Anyway, my idea was to make a higher stool than this with cross bars to strengthen the leg support. I wanted to experiment with the top as I didn't have large enough material to make it out of one log. For this I intended to join 2 to 3 inch sections together to get a diameter of about 11 to 12 inches and another using 3 radial sections from a large log as shown below.
Five rectangular pieces of ash 2-3 inches wide and about 2 inches thick roughed-out from ash logs originally 20-24 inches long.
Three radial ash sections cut from a single log to a thickness of about 2 inches.

Three ash legs ready to be refined and shaped for the stool . Two of the legs are from one long 22 inch log that was cleaved down the centre and so produced legs with a similar curvature at the bottom. The other leg was from another similar length cleaved log but the shape was somewhat contrived with the axe and drawknife to match the others!!
Tools I used are: 1. Sharpened axe 2. Froe (to cleave but you can just use an axe). 3. Large Draw -Knife. 4. Large flat spokeshave (I find this useful for developing the shape but a smaller draw-knife would do or even a knife). 5. Roughing Plane (Veritas Scrub Plane). 6. Jointer Plane. 7. Rounding Plane. I already had all of these from previous work apart from the Rounding Plane (chairmaker's plane) that is used to make the round tenons on the legs and cross-spars. It is possible to use a pole lathe for this but as the wood isn't often straight it becomes more difficult. Of course it is possible to make straight legs rounded with a pole lathe and then it is a simple matter to cut the round tenons. I purchased a Rounding Plane made by Ray Lles (3/4 inch) (the Ashen Crafts ones are no longer available as new).

I made the top pieces by first cutting into cuboids with an axe and then selecting the best side for the top used a draw-knife and then roughing plane to remove wood to get a fairly flat surface. Finally a used the jointer plane to get a flat surface. I then selected an adjoining surface and did the same but this time using a set-square to get a 90 degrees corner. I then selected a possible thickness and with a marker-gauge marked for the next surface and so on until I had a good shape ready to dry. I wasn't sure how long it wood take to dry so I selected one piece and weighed it at 1 week intervals with it stored in an unheated workshop in the winter (outside temperatures around 10 C). Here are the results:
Week # Weight/g% reduction
0 1001
1 973 2.8
2 963 3.8
3                   954                                       4.7
4                   943                                       5.8
5                   943                                       5.8
6                   945                                       5.6
When dry enough, my plan was to finally match the surfaces (with more use of the jointer plane) and  then glue before shaping to a disc but more of that later.

The legs were made from 22 inch length logs split down the middle so the two pieces matched. Each section was cut with a draw-knife to form a rectangular cross section. Then the corners were removed to form an octagonal shape. Further shaping was done with the spokeshave to get a good curvature, uniform thickness and elliptical cross section (as shown in the picture above). Further shaping was done to achieve a leg that was slimmer at the top to accommodate the cylindrical tenon and also at the bottom for standing with ample wood in between for the cross-spar mortices.
This is the first leg that I shaped with 3/4 inch tenon  (2 inches long) cut at the top.
The shape was partly decided by following the grain in the wood so that the bottom of the leg curved out, was thinner at the top and bottom with the thicker part in the centre for the cross-bars. I refined the shape by first marking a circle 1 inch diameter on the top surface of the leg and then shaving wood to get to that diameter. I then used the rotary plane to produce  a taper and 2 inch long 3/4 inch cylinder for insertion through the stool seat. Two sides of the leg were straight (looking at 90 degrees to the stool) so they were reduced first. The other sides had a curvature at the bottom and the leg also tapered at the bottom. I did most of this reduction by eye with the large spoke shave. I finished off with a small spoke shave and 80/240  grit abrasive. The other two legs were done in the same way but using the first leg as a template to develop the right profile.

I then figured out a way to set the legs through the top. First I made a small jig out of some waste redwood. The purpose of this was to align the auger bit at 10 degrees from the vertical to allow a hole to be drilled through about 5 cm thickness seat.
Jig for assistance in drilling leg holes in the seat. I used a traditional auger bit (11/16 th inch diameter) that was about 18 cm long. The guide hole is 13 cm depth set at 10 degrees to the vertical. Note the pencil line used when aligning the block on the seat before drilling. This line also extends over the front and rear faces of the large block.
The small block on top was predrilled by hand and set into the top of the larger block to a depth of about 1 cm and glued into position. This was then used as a guide to drill though the larger block. A centre line was drawn around the large block to aid positioning of the jig.

The jig was tested using a waste piece of 15 mm thickness pine sawn to a diameter of 12 inches. A circle of diameter 12 inches was scribed on the top and a hexagon drawn with sides 6 inches in length.. From this an equilateral triangle was drawn as shown below.
The seat top showing the geometry defining the position of the legs.  This was only a trial with joined pine wood to test the jig and methodology 
The centre of each side of the triangle was marked to show the position of each leg. The jig was then clamped in position on the seat so that the drill contacted the marked position and also aligned in a direction facing an apex of the hexagon to the rear and front of the block (the line also going through centre underneath the block). A board was also clamped to prevent break-through when drilling by hand.
The trial seat with legs partly inserted. With the actual ash seat (about 5 cm thick), the top of the legs will go through the seat and be wedged with beech. Also the stool will have two ash strechers to strenghten it.
I will continue the construction when the seat timber is dry enough.

After about 2 months (see drying table shown above) I decided to continue with the top. I planed the boards with the jointing plane and then joined with glue and dowel pegs. I positioned the dowels using dowel pins to get good alignment. Once set, I planed the top and bottom of the seat to get level and flat with particular attention to the top of the seat. I then used a scribe to find the seat centre and work out the maximum diameter of the seat. I then marked the centre and scribed the seat top. The next job was to cut the seat cylinder using a traditional turning saw. I had tried an electrical jig saw but the seat thickness was too much for the blade and the turning saw was easy going. After that I used a block plane to trim the seat edge to the correct scribed diameter and the smoothing plane to remove any excess wood from the underside of the seat so that it was a uniform thickness.
I then marked out the top of the seat for the leg holes. I did this by drawing an equilateral triangle with the apices on the edge of the circle defining the seat diameter (see picture below). I found it difficult to mark the internal angles of 60 degrees so instead calculated the length of the triangle side (radius from the scribe x square root (3)) and marked the three points. Marking the triangle, the legs holes were marked half-way along each side. I then placed the drill jig with the bit protruding to the mark, clamped it in the correct position and drilled through to a back board. This worked well.
Stool top after gluing boards together and making leg holes. The top has to be shaped and prepared for making the leg stretchers.
I then marked bevels on the top and underside of the seat using the scribe (about 6 mm from edge) and with a marking gauge marked about 6 mm from the top and 1 cm on the edge side of the seat. I planed these with a block plane and tidied with a large spoke shave.

The next step was to prepare a stretcher between two of the legs. To do this I installed the legs to the correct positions and marked their orientation on the tops. I then judged a vertical position of the stretcher that looked right and measured the distance from the bottom of the seat and marked this on both legs. I put the stool on the bench with the seat at the bottom and legs up. Because the legs are slightly different I was careful to locate the centre for the holes for the stretcher on the inside of the legs and then mark the line around the leg to estimate the position of the hole on the outside.  This line needed to be horizontal (i.e. parallel to the floor) and hence at an angle to the surface of the leg. I also estimated this angle with an adjustable square. The next stage was to drill the holes for the stretcher in both legs. This proved straight forward by clamping the leg in a vice and adjusting the angle of the leg in the vice so that the drill would be central on the leg and also horizontal. To do this I used the ratchet on the brace and kept a close eye on the direction of the bit relative to the bench top. Hence it was easy to keep the drill bit horizontal (measure against the bench top) and central on the leg. Once the drill screw pierced the opposite surface, I reversed the leg and drilled from the other side to produce a clean hole.

I made the stretcher by using the draw-knife to make a round blank of about the correct length for the stool. I then shaped it so that the end fitted into the 3/4 inch Rounding Plane and the centre was large enough to accommodate the cross-stretcher. I then used the Rounding Plane to shape the ends of the stretcher to a depth of 5 cm (the diameter of the legs). Finally, I used a large Spokeshave to shape the stretcher and make it symmetrical ready for fixing as shown below.

The first stretcher installed ready to mark the second one. It is of course necessary to remove the legs to install the stretcher. The stretcher still needs to be finished and fitted with glue and wedges.
The cross stretcher was made in a similar way but this time the hole in the first stretcher was made smaller (9/16 th inch) because of the smaller diameter of the stretcher compared with the legs. I formed the shape of this on the pole lathe, reducing the last 1 1/2 inches to 9/16 th measured with Vernier calipers. I then used the 3/4 inch Rounding Plane for the other side of the stretcher and shaped the rest with the large Spokeshave. Obviously it is important to measure the distance between the leg and the first stretcher so that the uniform diameters at the end of the new stretcher extend far enough. In fact it would have been easier to make the whole stretcher with the lathe although the oval shape at the centre of the stretcher would have been lost. It only remained to drill the appropriate holes. This seemed a little daunting at first because of the non-regular shape of the legs and the angles involved. However it was straight forward, basically putting the stool together to the marks previously made, and then finding the centre of the first stretcher and using a steel ruler and spirit level to locate the centre on the opposite leg. I then used a plastic flexible ruler to mark the opposite side of the stretcher and leg and sliding bevel to get the angle on the leg. The holes were drilled with a brace using the work bench and sliding bevel to judge the angles and direction.
The stool legs with both stretchers installed and ready for finishing and installation with beech wedges.

Now (beginning of July) five months later and the parts were left in the workshop over the winter and spring. It only remained to put the stool together, install wedges in the joints, glue and finish.
Finished stool after treating with Shellac, Dutch Oil and Wax. 
The final construction was made more complicated because the Ash had dried further after shaping and making the joints. I made the mistake of making the joints prior to complete drying and so the tenons were smaller than ideal. Although I had left them two month to dry, that is clearly not enough or perhaps the higher temperatures in the Spring and Summer had some effect. With the foot-stool (see below), I made the tenons after the wood was dried longer and obtained a snug-fit.  Also the top had moved a little and had to be planed flat again. In retrospect, the top should have been joined after drying. In future when working with greenwood, I will do the main roughing-out and pole lathe work with the fresh wood and then allow it the dry slowly by sealing the end grain. After drying I will then do the joinery. Assessing the dryness of the wood is pretty crucial to the joinery.
 In all it was a challenge to take a log of Ash and use the intrinsic shape to make the curved legs and choose wood for the top. By splitting the log I was able to get some matching symmetry for two of the legs. The geometry to get the mortices correct is difficult but possible given some flexibility in the placement of the stretchers.

Square footstool.

I also decided to use some of the ash to make a square footstool of similar design to the solid seat stool described in the book by Jack Hill ("Country Chair Making"). For this I used the three larger timbers described above and joined them with dowels. First I got the surfaces square using the jointing plane and then used dowel pins to locate the holes for the dowels. The boards were then cut to approximately the chosen size (about 9 x 9 inches) and then glued / clamped. When the top was dry I marked out the top and planed the main surfaces flat, first with the roughing plane and then the smoothing plane. The final board was 1 3/8 inch thick and 9 x 9 inches and perfectly square.

I didn't follow the dimensions given in Hill's book for positioning the leg. I increased the angle from 20 degrees to 25 degrees and then calculated the position of the legs across the diagonals. This was 3.1 inches on the bottom side of the seat and 3.7 inches on the top (measured from the corners of the seat) with a stool height of 8 inches.

The footstool seat with one of the leg holes drilled. A new drill guide was made (shown on the right) using some waste beech so that it could be clamped to the top of the seat with the centre line along the diagonal.
Drilling a leg hole using a 1 inch auger and jig to get the correct angle.

I then made the four stool legs using silver birch branches. These were from some pruning from a nearby orchard and about 4 inches diameter with the bark on. I decided to shape these on the pole lathe. I cut them to about 11 inches in length and used the axe to remove the bark and side branches. I then marked the centres and turned about 2 cm on each end on the lathe and then used a draw-knife to make a cylinder between the two turned ends. I then turned the legs (I was aiming for a stool height of 8 inches) allowing 2 inches for the tenons (I turned to 1 1/8 inches to allow for shrinkage) and shaped so the maximum diameter of 1 1/2 inches was 4 1/2 inches from the top of the stool. I turned the lower part of the leg to mirror the upper and reducing to 1 1/8 inches at the foot of the stool and allowed about 1 inch spare to adjust the height as needed.
Silver Birch stool legs immediately after turning. The top tenons are shown at the bottom. The ends of the legs were coated with beeswax and put in a paper bag to dry together with some shavings from the lathe. The plan is to refine the legs when they are dry and make the 1 inch tenons accurately with a rounding plane. The legs can still be mounted on the lathe for adjustments and sanding as needed.

Now about five months later having left the wood in the workshop over the winter and spring. I prepared the top of the stool using a scraper and sand paper down to 350 grit. Because of the varied grain pattern, the scraper worked better than a plane. I put the legs back on the lathe to do the final preparation of sanding and marked two concentric rings with the skew chisel. The legs had not cracked or distorted but the top of the stool had a slight concave that I rectified by planing.  The next step was to use the 1 inch rounding plane to form the final shape of the tenons. I had to use a spoke-shave to get the slope on the legs to fit the plane as without doing this the plane caused some tearing of the wood. I did one leg first and from this did more work on the pole lathe to shape the upper part of the other legs for use with the rounding plane. Each leg was then fitted into the mortices by making fine adjustments to the tenons using sandpaper to get a close fit. 
The stool was then put together and the lines for the wedges to fit the legs were marked so that they went across the grain of the top to avoid splitting the top when tightened. I prepared wedges from some waste beech, sawed the wedge-cut in the tenons, glued the legs in position and inserted the wedges. It was then only a matter of sawing off the waste from the top of the legs, chiselling them to fit flush with the top and doing the final preparations before treating with Shellac and Dutch oil.
Final foot stool, Ash top and Silver Birch legs
Foot stool; Ash top and Silver Birch legs.